We have unearthed this great article pertaining to Installing A Bathtub down the page on the web and thought it made good sense to discuss it with you here.
Mounting a bathtub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is additionally a moderately tough task. If the old tub is conveniently obtainable, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub and place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and set in the brand-new one. See to it you have actually qualified on your own for the work as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to think about employing one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This post will aid you install a brand-new bath tub in your washroom if you have already purchased a brand-new tub and also don't need to transform the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to prevent stress on the tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of removing the existing taps can be quite troublesome as a result of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bathtub in the required position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub up until the spirit level reads level.
To install taps, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the supply of water and inspect all joints and new pipework for leakages and tighten them if essential. Fill the tub and also examine the overflow electrical outlet and the regular outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub needs to wait until the bath tub has been utilized a minimum of when as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Safeguard the faucet in place with the supplier given backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind ought to be connected to the tap finishes first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break an inflexible seal, creating the water to permeate the wall between the bath as well as the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in use. The sealer can fracture rather very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been brought to that editorial on A Step-by-Step Guide to Installing a Bathtub through a friend on our other web blog. Sharing is nice. Who knows, you may very well be doing someone a favor. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Emergency? Depend on our professionals.